DI-9M-08CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
 |
  |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 。∕2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
 | Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-08CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 。∕2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-08日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 。∕2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-08日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 。∕2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
最新產品
- 現貨750-402 2025/9/21 23:07:30
- 現貨RBT 2-V(SB) 7PX0.2SQ K 2025/9/21 23:06:42
- 現貨330104-00-12-05-02-00 2025/9/21 23:05:56
- @市場推送SWL025A-FFF 2025/9/21 23:03:29
- 推出DX-U RS-232C 2025/9/21 23:02:52
- 推出PFXGP4105G1D 2025/9/21 23:02:11
- 主推V-RFM-01A HN24618A HN24619A HN24620A 2025/9/21 23:01:37
- @市場推選KB7R1-02/JEV06267-001C KB7R2-02/JEV06241-001 2025/9/21 22:58:42
- @商務主推P6100 2100002 2025/9/21 22:57:34
- 推送6,9URD30TTF0160 / W300054 2025/9/21 22:56:31
- @商務推出CIMR-JT2A0002BAA 2025/9/21 22:55:12
- @市場推送RKC CB100L 2025/9/21 22:52:28
- 推選6FC5312-0DA00-0AA0 2025/9/21 22:51:38
- @商務主推1395-142129 2025/9/21 22:50:56
- 推選HG-KR13B 2025/9/21 22:50:02
- 推出ZSE30A-01-A-M P601010-13-3 2025/9/21 22:47:32
- @采購?fù)七xAJ65SBT-64AD 2025/9/21 22:46:56
- @采購?fù)七xP9B10VN 2025/9/21 22:45:52
- @采購?fù)七xHG-KR43B 2025/9/21 22:45:10
- 推選6ES5374-1FH21 2025/9/21 22:42:12
- 推選PFXGM4301TAD 2025/9/21 22:41:29
- @采購?fù)七xK6KF K6KF-01 JEV04190-002B 2025/9/21 22:40:54
- @市場推選FR-E740-0.75K 2025/9/21 22:40:08
- @商務推出330101-00-08-10-02-00 2025/9/21 22:37:26
- 現貨MAXQ-02 JEV00417-4 2025/9/21 22:36:41
- @商務主推FR-E720-0.4K 2025/9/21 22:36:08
- 推出STP4A-4121A024M 2025/9/21 22:35:19
- @商務主推SGMAH-04AAA21 2025/9/21 22:32:49
- @商務主推DSCK-5t 2025/9/21 22:32:02
- @采購?fù)七x1756M16SE 2025/9/21 22:31:25