DI-9M-8日本思達電批扭力測試儀

        Management of electrik screw driver
        仠Torque Meter 丂DI-9M-8/08
        DI-9 series is most suitable for checkingcontrolling the torque of Electric ScrewdriverTorque Driver.
        upgradeThe main changed parts (1) In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. (2) Change of Measurement Unit Can be Performed   N-m <=> kgf-cm <=>lbf-in  Etc. (3) Setup of Various Numerical Values Can be EasyCan Carry Out Speedily. (4) Calculation of Maximum, Minimum,Average Became Intelligible. (5) The call of the saved data became easy. The output of data also became intelligible. (6) Fault charge protection. It is pilot-lamp lighting during charge. (7) Data Output is USB Form (B Type). (8) Memory Data are 800 Affairs (9) Real-time Output is Every 1 / 180 Seconds.
        The best for everyday check of an electric driver Wide measurement range (0 - 8000digit), it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint (PAT.P).
        Specification DI-9M-8 DI-9M-08
        Measuring range 0.020-8 N 2.0-800 mN
        0.20乣80 kgf丒cm
        0.020乣8 kgf丒cm
        0.20乣70 lbf丒in 0.020乣7 lbf丒in
        Accuracy   亇0.5% (499 digit or less 亇3digit)
        Display The 4 figures digital display of LCD
        The measurement direction CW-CCW (rightleft)
        Zero return by one touch Return to zero by pressing clear button.
        Measurement   Mode
        Track , P-P(peak to peak) , P-D(Peak-Down) , C(Real-time Output)
        Highlow limits judging function
        Highlow value are measurement within the limits,can be set up.
        Real-time Output
        Load torque value is outputted every about1/ 180 second.
        The Maximum, the minimum,the average value display
        The maximum, the minimum, average value,the data number of 30 data are displayed.It saves to ten channels.
        Data Output ASCII format (baud rate 19200)
        Auto power save 10 minutes no use, automatically switch off.
        Power supply Ni-Cd chargeable battery 1.2V 亊 5cells 700mAh
        Charging time About 3hours
        Continuous working time About 12hours
        clearance It is a display clearance in set-up time.   (0.1 - 3.0 sec)
        Socket size 仩 20mm/ 仩9.5mm
        Dimension / Weight W:160亊D:125亊H:55 / About 1kg
        Recommend buffer accessories Measuring joint OW-20/OW-60 Measuring joint OW-025/OW-10
        Cube (with a 5th page screw hole)丂20x20x20 丂(M2.6/M3/M4/M5/M6 Tap processing)
        AC/DC adaptor
        Exclusive receipt case
        An inspection report, a proofreading certificate, a traceability system figure

        仸Do not use for measurement of impact tool.Do not apply more than the specified torque. 

        仠 MEASURING JOINT OW series
        OW joint   Since our company developed the buffer     with little influence of fricative,     stable measurement could be performed    Moreover ,it does not need to reverse-rotate     at the time of  measurement,    work efficiency  improved.
        Specification Type
        OW-025 OW-10 OW-20 OW-60
        Measuring range   N 0.25 1 2 6
        Mechanical life   乮times乯 10,000 8,000 5,000 5,000
        Outer diameter size 乮mm乯 Bit engagement part (screw part) M2.6 cross recess screw M3 cross recess screw M4 cross recess screw M6 cross recess screw
        The standard screw is cross recess screw but they may be altered as necessary
        Outside diameter 冇28 冇32 冇32 冇38
        Height 44 51 51 69
        俬nstallation 20square 亊4(t)

        CD-10M日本思達電批扭力測試儀

        Management of electric screw driver
        仠Torque Meter 丂CD-100M/10M
        upgradeThe main changed parts (1) In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. (2) Change of Measurement Unit Can be Performed   N-m <=> kgf-cm <=>lbf-in  Etc. (3) Setup of Various Numerical Values Can be EasyCan Carry Out Speedily. (4) Calculation of Maximum, Minimum,Average Became Intelligible. (5) The call of the saved data became easy. The output of data also became intelligible. (6) Fault charge protection. It is pilot-lamp lighting during charge. (7) Data Output is USB Form (B Type). (8) Memory Data are 800 Affairs (9) Real-time Output is Every 1 / 180 Seconds.
        Specification CD亅100M CD亅10M
        Measuring range   (at the time of Track) 0.10乣10丂N丒m 1.0乣100丂們N丒m丂
        1.0乣100 kgf丒cm 0.10乣10 kgf丒cm
        1.0乣90 lbf丒in 0.10乣9 lbf丒in
        Accuracy 亇0.5亾乮F/S乯(199 or less digit亇1digit)
        Display The 3.5 figures digital display of LCD
        The measurement direction CW-CCW (rightleft)
        Measurement   Mode Track , P-P(peak to peak) , P-D(Peak-Down) , C(Real-time Output)
        Highlow limits judging function Highlow value are measurement within the limits,can be set up.
        Real-time Output Load torque value is outputted every about1/ 180 second.
        The Maximum, the minimum,the average value display The maximum, the minimum, average value,the data number of 30 data are displayed.It saves to ten channels.
        Automatic Clearance Automatically clear the displayed value after certain time (0.5 - 3.0 sec,selectable at each 0.5 sec). Setting 0.0 sec for manual Zero clearance
        One-touch zero A clear button is pushedit is a zero.丂 Data is outputed.
        Data output ASCII format (baud rate 19200)
        Power supply Ni-Cd chargeable battery 1.2V亊5cells 700mAh
        Auto power save 10 minutes no use, automatically switch off.
        Charging time About 3 hours
        Continunous working time About 12 hours
        Socket fit mouth 仩 20mm/ 仩9.5mm
        Weight  Abbreviation   1 kg
        Outside dimension 160乮W乯亊125乮D乯亊55乮H乯
        Attachment Measurement joint丂SJ50/SJ10K Measurement joint丂SJ10
        Accessories (one piece each)
        AC/DC adaptor
        Exclusive receipt case
        An inspection report, a proofreading certificate, traceability system figure
        SJ50 SJ10 About an adapter 亙measurement joint丂SJ乮PAT.P乯
        SJ-50 SJ-10 It does not decompose, even if it rewinds joint too much Since the adapter attached is the coil spring compression system of the conventional system, you can use it by the conventional management method. Moreover, this adapter is special structure. It does not decompose, even if it rewinds joint too much. You can use it in comfort.

        CD-10、CD-100思達電批扭力測試儀

        日本思達牌電批扭力測試儀

        型號

        DI-9-08

        DI-9-08

        CD-10

        CD-100

        測試范圍

        0.1~800mN.m 0.001~8kgf.cm 0.001~7Lbf.in

        0.001~8N.m 0.01~80kgf.cm 0.01~70Lbf.in

        0.001~1N.m 0.01~10kgf.cm 0.01~9Lbf.in

        0.01~10N.m 0.1~100kgf.cm 0.1~90Lbf.in

        誤差

        ±0.5%

        ±0.5%

        功能

        LC:LCD液晶顯示,RS:帶RS232輸出口,PO:電源自動關閉功能,IO:設定自動清零

        外型尺寸

        155W×125D×55H

        配件

        測量頭OW025/OW10包 裝盒/AC充電器各一個

        測量頭OW020/OW60包 裝盒/AC充電器各一個

        連接頭SJ10/包裝 盒/AC充電器各一個

        連接頭SJ50包裝盒 /AC充電器各一個

         
        規格 CD-100 CD-10
        測試范圍 3.0-800.0 mNm 0.030-8.000 N叮
        精度 8000-500 digit 0.5% 499-30 digit within3digit
        顯示單位 lbfin-kgfcm-Nm
        歸零 Return to zero by pressing clear button.
        Data spec. Data output Based on RS232C Baud rate:9600
        Power supply Auto power off 自動電源關閉 10 min.
        Battery drive Ni-Cd 1.2V 5cells1200mAh
        充電時間 8hrs.
        連續充電時間 20hrs.
        自動歸零 配備自動歸零裝置
        尺寸 W:155D:125H:30 / 1kg
        附件 Measuring joint SJ10/50 Measuring joint SJ10

        CD-10、CD-100日本思達電批扭力測試儀

        日本思達牌電批扭力測試儀

        型號

        DI-9-08

        DI-9-08

        CD-10

        CD-100

        測試范圍

        0.1~800mN.m0.001~8kgf.cm0.001~7Lbf.in

        0.001~8N.m0.01~80kgf.cm0.01~70Lbf.in

        0.001~1N.m0.01~10kgf.cm0.01~9Lbf.in

        0.01~10N.m0.1~100kgf.cm0.1~90Lbf.in

        誤差

        ±0.5%

        ±0.5%

        功能

        LC:LCD液晶顯示,RS:帶RS232輸出口,PO:電源自動關閉功能,IO:設定自動清零

        外型尺寸

        155W×125D×55H

        配件

        測量頭OW025/OW10包裝盒/AC充電器各一個

        測量頭OW020/OW60包裝盒/AC充電器各一個

        連接頭SJ10/包裝盒/AC充電器各一個

        連接頭SJ50包裝盒/AC充電器各一個

         
        規格CD-100CD-10
        測試范圍3.0-800.0 mNm0.030-8.000 N叮
        精度8000-500 digit 0.5% 499-30 digit within3digit
        顯示單位lbfin-kgfcm-Nm
        歸零Return to zero by pressing clear button.
        Data spec.Data outputBased on RS232C Baud rate:9600
        Power supplyAuto power off自動電源關閉 10 min.
        Battery driveNi-Cd 1.2V 5cells1200mAh
        充電時間8hrs.
        連續充電時間20hrs.
        自動歸零配備自動歸零裝置
        尺寸W:155D:125H:30 / 1kg
        附件Measuring jointSJ10/50Measuring jointSJ10

        DI-IM-IP200日本思達電批扭力測試儀

        Management of air tool / oil pulse tool
        仠Torque Tester 丂DI-1M-IP丂series
        DI-1M-IP50
        Management of an oil pulse tool etc. High precisionlightweight small. The best for everyday check of an oil pulse tool. Since it is highly precise, the bolting tool of a bolt is manageable on the optimal conditions. Since it is lightweightsmall, it can install in a work line. Convenient for the scheduled inspection of a tool It is brightreadable at an LED display. The high luminosity (light emitting diode) LED can be adopted as a display element,  and measured value can be read also in a dark place It can use also for a torque wrench. It can be used also for management of a torque wrench angle nut runner besides an oil pulse wrench. The main features 仩Blow counter. The total number of blows within fixed timetorque measured value are displayed. 仩 Stable measurement can be performed in inspection of a pre set torque wrench in peak down mode. 仩RS232C Output. It connects with data printing (printer use corresponding to RS232C),a personal computer,data can be saved easily.(Taking-in soft use of exclusive use)  仩 It is the highly efficient measuring instrument which carried the auto-power-off function, the auto clear function, etc.  
        Specification 俢俬-侾俵-俬俹俆侽 俢俬-侾俵-俬俹俀侽侽 俢俬-侾俵-俬俹俆侽侽
        Measuring range   (at the time of Track)
        0.30乣50 N 3.0乣500 kgf丒cm 3.0乣430 lbf丒in
        3.0乣200 N 30乣2000 kgf丒cm 30乣1800 lbf丒in
        3.0乣500 N 30乣5000 kgf丒cm 30乣4500 lbf丒in
         Peak down Operating range 0.70N?/span>m, 7.0kgfcm/ lbfin 7.0N?/span>m, 70kgfcm/ lbfin
        Accuracy 亇0.5亾乮F/S乯(499 or less digit亇3digit)
        Display The 4 figures digital display of LED
        The measurement direction CW-CCW (rightleft)
        Measuring mode P-P  Peak Peak load value hold
        T-R  Track Indication of real time torque value.
        P-D  Peak down Indication peak down pointhold.
        Display zero clearance Automatically clear the displayed value after certain time (0.5 - 3.0 sec,selectable at each 0.5 sec). Setting 0.0 sec for manual Zero clearance
        Blow Measurement range Zero to 99 blow
        Measurement time 0.1 - 9.9 seconds
        Data output RS232C conformity (baud rate 9600)
        Power supply Ni-Cd chargeable battery 1.2V亊5cells 700mAh
        Auto power save 5 minutes no use, automatically switch off.
        Charging time From empty - less than 6hours
        Continunous working time 8 hours
        Meter part丂Weight About 600g
        Detection part丂Weight about 600g about 1kg about 2.5kg
        Meter part丂Outside size 146(W)亊115(D)亊48(H) 乮It does not contain by the projection part乯
        Code length Standard 1m (there are automatic machines no less than 4m as an option.)
        Accessories (one piece each)
        Attache case
        AC/DC adaptor (Please choose AC adaptor out of 120V,230V.)
        An inspection report, a proofreading certificate, traceability system figure
        Detection machine size figure
        Detection machine outside figure
        Form 俬俹俆侽 俬俹俀侽侽 俬俹俆侽侽 Detector size
        兂50 兂60 兂80
        63 73 99
        10 10 15.5
        兂90 兂110 兂140
        兂74 兂90 兂116
        (Three division) 兂6.3 兂8.3 兂10.5
        俧丂(Socket intuition affinity) 9.5倱倯 12.7倱倯 19倱倯
        Weight 632g 1.8kg 3kg

        DI-9M-8日本思達電批扭力測試儀

        Management of electrik screw driver
        仠Torque Meter 丂DI-9M-8/08
        DI-9 series is most suitable for checkingcontrolling the torque of Electric ScrewdriverTorque Driver.
        upgradeThe main changed parts (1) In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. (2) Change of Measurement Unit Can be Performed   N-m <=> kgf-cm <=>lbf-in  Etc. (3) Setup of Various Numerical Values Can be EasyCan Carry Out Speedily. (4) Calculation of Maximum, Minimum,Average Became Intelligible. (5) The call of the saved data became easy. The output of data also became intelligible. (6) Fault charge protection. It is pilot-lamp lighting during charge. (7) Data Output is USB Form (B Type). (8) Memory Data are 800 Affairs (9) Real-time Output is Every 1 / 180 Seconds.
        The best for everyday check of an electric driver Wide measurement range (0 - 8000digit), it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint (PAT.P).
        Specification DI-9M-8 DI-9M-08
        Measuring range 0.020-8 N 2.0-800 mN
        0.20乣80 kgf丒cm
        0.020乣8 kgf丒cm
        0.20乣70 lbf丒in 0.020乣7 lbf丒in
        Accuracy   亇0.5% (499 digit or less 亇3digit)
        Display The 4 figures digital display of LCD
        The measurement direction CW-CCW (rightleft)
        Zero return by one touch Return to zero by pressing clear button.
        Measurement   Mode
        Track , P-P(peak to peak) , P-D(Peak-Down) , C(Real-time Output)
        Highlow limits judging function
        Highlow value are measurement within the limits,can be set up.
        Real-time Output
        Load torque value is outputted every about1/ 180 second.
        The Maximum, the minimum,the average value display
        The maximum, the minimum, average value,the data number of 30 data are displayed.It saves to ten channels.
        Data Output ASCII format (baud rate 19200)
        Auto power save 10 minutes no use, automatically switch off.
        Power supply Ni-Cd chargeable battery 1.2V 亊 5cells 700mAh
        Charging time About 3hours
        Continuous working time About 12hours
        clearance It is a display clearance in set-up time.   (0.1 - 3.0 sec)
        Socket size 仩 20mm/ 仩9.5mm
        Dimension / Weight W:160亊D:125亊H:55 / About 1kg
        Recommend buffer accessories Measuring joint OW-20/OW-60 Measuring joint OW-025/OW-10
        Cube (with a 5th page screw hole)丂20x20x20 丂(M2.6/M3/M4/M5/M6 Tap processing)
        AC/DC adaptor
        Exclusive receipt case
        An inspection report, a proofreading certificate, a traceability system figure

        仸Do not use for measurement of impact tool.Do not apply more than the specified torque. 

        仠 MEASURING JOINT OW series
        OW joint   Since our company developed the buffer     with little influence of fricative,     stable measurement could be performed    Moreover ,it does not need to reverse-rotate     at the time of  measurement,    work efficiency  improved.
        Specification Type
        OW-025 OW-10 OW-20 OW-60
        Measuring range   N 0.25 1 2 6
        Mechanical life   乮times乯 10,000 8,000 5,000 5,000
        Outer diameter size 乮mm乯 Bit engagement part (screw part) M2.6 cross recess screw M3 cross recess screw M4 cross recess screw M6 cross recess screw
        The standard screw is cross recess screw but they may be altered as necessary
        Outside diameter 冇28 冇32 冇32 冇38
        Height 44 51 51 69
        俬nstallation 20square 亊4(t)

        CD-10M日本思達電批扭力測試儀

        Management of electric screw driver
        仠Torque Meter 丂CD-100M/10M
        upgradeThe main changed parts (1) In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. (2) Change of Measurement Unit Can be Performed   N-m <=> kgf-cm <=>lbf-in  Etc. (3) Setup of Various Numerical Values Can be EasyCan Carry Out Speedily. (4) Calculation of Maximum, Minimum,Average Became Intelligible. (5) The call of the saved data became easy. The output of data also became intelligible. (6) Fault charge protection. It is pilot-lamp lighting during charge. (7) Data Output is USB Form (B Type). (8) Memory Data are 800 Affairs (9) Real-time Output is Every 1 / 180 Seconds.
        Specification CD亅100M CD亅10M
        Measuring range   (at the time of Track) 0.10乣10丂N丒m 1.0乣100丂們N丒m丂
        1.0乣100 kgf丒cm 0.10乣10 kgf丒cm
        1.0乣90 lbf丒in 0.10乣9 lbf丒in
        Accuracy 亇0.5亾乮F/S乯(199 or less digit亇1digit)
        Display The 3.5 figures digital display of LCD
        The measurement direction CW-CCW (rightleft)
        Measurement   Mode Track , P-P(peak to peak) , P-D(Peak-Down) , C(Real-time Output)
        Highlow limits judging function Highlow value are measurement within the limits,can be set up.
        Real-time Output Load torque value is outputted every about1/ 180 second.
        The Maximum, the minimum,the average value display The maximum, the minimum, average value,the data number of 30 data are displayed.It saves to ten channels.
        Automatic Clearance Automatically clear the displayed value after certain time (0.5 - 3.0 sec,selectable at each 0.5 sec). Setting 0.0 sec for manual Zero clearance
        One-touch zero A clear button is pushedit is a zero.丂 Data is outputed.
        Data output ASCII format (baud rate 19200)
        Power supply Ni-Cd chargeable battery 1.2V亊5cells 700mAh
        Auto power save 10 minutes no use, automatically switch off.
        Charging time About 3 hours
        Continunous working time About 12 hours
        Socket fit mouth 仩 20mm/ 仩9.5mm
        Weight  Abbreviation   1 kg
        Outside dimension 160乮W乯亊125乮D乯亊55乮H乯
        Attachment Measurement joint丂SJ50/SJ10K Measurement joint丂SJ10
        Accessories (one piece each)
        AC/DC adaptor
        Exclusive receipt case
        An inspection report, a proofreading certificate, traceability system figure
        SJ50 SJ10 About an adapter 亙measurement joint丂SJ乮PAT.P乯
        SJ-50 SJ-10 It does not decompose, even if it rewinds joint too much Since the adapter attached is the coil spring compression system of the conventional system, you can use it by the conventional management method. Moreover, this adapter is special structure. It does not decompose, even if it rewinds joint too much. You can use it in comfort.

        CD-10/CD-100上海騰鉆電批扭力測試儀,思達電批扭力測試儀

         
        日本思達牌CD-10/CD-100電批扭力測試儀

         
           詳細介紹
        相關產品名稱:扭力起子,數顯扭力起子,扭力起子測試儀,扭力起子檢測儀,扭力計

        品名稱: 電批扭力測試儀cd-10/cd-100 制 造 商: 思達(cedar) 產品種類: 測力、拉力儀器

         

        日本思達牌電批扭力測試儀

        型號

        DI-9-08

        DI-9-08

        CD-10

        CD-100

         

         

         

         

         

         

         

         

        測試范圍

        0.1~800mn.m0.001~8kgf.cm0.001~7lbf.in

        0.001~8n.m0.01~80kgf.cm0.01~70lbf.in

        0.001~1n.m0.01~10kgf.cm0.01~9lbf.in

        0.01~10n.m0.1~100kgf.cm0.1~90lbf.in

        誤差

        ±0.5%

        ±0.5%

        功能

        lc:lcd液晶顯示,rs:帶rs232輸出口,po:電源自動關閉功能,io:設定自動清零

        外型尺寸

        155(w)×125(d)×55(h)

        配件

        測量頭ow025/ow10包裝盒/ac充電器各一個

        測量頭ow020/ow60包裝盒/ac充電器各一個

        連接頭sj10/包裝盒/ac充電器各一個

        連接頭sj50包裝盒/ac充電器各一個

         

        該公司產品分類: 線材張力計 東日扭力工具 溫濕度記錄儀 皮帶張力計 張力計 測量儀器 環境測試儀器 測量量具及輔助工具 扭力工具 測量工具 機床配件 光學儀器 儀器儀表

        DI-9-08/DI-9_8上海電批扭力測試儀,思達電批扭力測試儀

         
        日本思達牌DI-9-08/DI-9_8電批扭力測試儀

         
           詳細介紹
        相關產品名稱:扭力起子,數顯扭力起子,扭力起子測試儀,扭力起子檢測儀,扭力計

        產品名稱: 電批扭力測試儀DI-9-08/DI-9-08 制 造 商: 思達(CEDAR) 產品種類: 測力、拉力儀器

         

         

        日本思達牌電批扭力測試儀

        型號

        DI-9-08

        DI-9-08

        CD-10

        CD-100

        測試范圍

        0.1~800mn.m0.001~8kgf.cm0.001~7lbf.in

        0.001~8n.m0.01~80kgf.cm0.01~70lbf.in

        0.001~1n.m0.01~10kgf.cm0.01~9lbf.in

        0.01~10n.m0.1~100kgf.cm0.1~90lbf.in

        誤差

        ±0.5%

        ±0.5%

        功能

        lc:lcd液晶顯示,rs:帶rs232輸出口,po:電源自動關閉功能,io:設定自動清零

        外型尺寸

        155(w)×125(d)×55(h)

        配件

        測量頭ow025/ow10包裝盒/ac充電器各一個

        測量頭ow020/ow60包裝盒/ac充電器各一個

        連接頭sj10/包裝盒/ac充電器各一個

        連接頭sj50包裝盒/ac充電器各一個

         

         

        該公司產品分類: 線材張力計 東日扭力工具 溫濕度記錄儀 皮帶張力計 張力計 測量儀器 環境測試儀器 測量量具及輔助工具 扭力工具 測量工具 機床配件 光學儀器 儀器儀表

        DI-9-08日本CEDAR思達電批扭力測試儀

        日本思達牌電批扭力測試儀

        型號

        DI-9-08

        DI-9-08

        CD-10

        CD-100

        測試范圍

        0.1~800mN.m 0.001~8kgf.cm 0.001~7Lbf.in

        0.001~8N.m 0.01~80kgf.cm 0.01~70Lbf.in

        0.001~1N.m 0.01~10kgf.cm 0.01~9Lbf.in

        0.01~10N.m 0.1~100kgf.cm 0.1~90Lbf.in

        誤差

        ±0.5%

        ±0.5%

        功能

        LC:LCD液晶顯示,RS:帶RS232輸出口,PO:電源自動關閉功能,IO:設定自動清零

        外型尺寸

        155W×125D×55H

        配件

        測量頭OW025/OW10包 裝盒/AC充電器各一個

        測量頭OW020/OW60包 裝盒/AC充電器各一個

        連接頭SJ10/包裝 盒/AC充電器各一個

        連接頭SJ50包裝盒 /AC充電器各一個

        最新產品

        熱門儀器: 液相色譜儀 氣相色譜儀 原子熒光光譜儀 可見分光光度計 液質聯用儀 壓力試驗機 酸度計(PH計) 離心機 高速離心機 冷凍離心機 生物顯微鏡 金相顯微鏡 標準物質 生物試劑
        久久久国产精品四虎,国产三级AV绿色在线一区,中文字幕第二页精品一区,综合亚洲网友自拍片